EOS 38.AS Guia de Instalação descarregar pdf (Página 3)

Special Instructions

Improper installation can create fire hazards!

Please read the installation guide carefully and

completely. Strict attention should be paid to

dimensional data and to the following special

instructions.

lThe sauna heating unit is designed for

operation with an input voltage of 400 V

AC 3N through the sauna control unit.

l Installation and electrical connection of the

sauna heating units, the control unit and other

electrical components must be performed by

a qualified electrician. The special safety

requirements specified in VDE 0110 v. § 49

DA/6 and VDE 0100, Part 703/2006-2 must be

observed during electrical installation.

l The sauna heating and control units may be

used only in sauna cabins constructed of

suitable, resin-free, untreated material (e.g.

Nordic spruce).

l The sauna cabin must have a minimum inside

height of 1.90 m.

l Only one sauna heater providing the required

heating output may be installed in the sauna

cabin (see Table 2).

l Every sauna cabin must have a fresh-air inlet

and an exhaust outlet. All ventilation inlets/

outlets must be positioned behind the sauna

heating unit and approx. 5-10 cm above the

floor. Minimum inlet/outlet dimensions are listed

in Table 1.

l The exhaust outlet must be positioned in the

lower section of the rear wall of the sauna

cabin, diagonally opposite the sauna heating

unit. Fresh-air inlets and exhaust outlets must

not be closed. Please observe the instructions

provided by your sauna cabin supplier.

l Caution: Covered or improperly filled

stone grates can cause fire hazards.

l Please ensure that no objects have been left

lying on the sauna heating unit prior to each

operatio

l Caution: Due to the high temperatures

generated during operation of the sauna

heating unit, direct contact with the unit

can cause burns.

l The sauna heating unit is not designed for

installation/use in a niche, beneath the reclining

bench or beneath an inclined ceiling.

l The sauna heating unit must not be operated

when the fresh-air inlet is closed.

l Cabin lighting and lighting installation

components must be splash-resistant

and suitable for operation at

environmental temperatures of up to

140°C. Therefore, only VDE-tested sauna

lighting systems (max. 40 Watt) may be

used in connection with the sauna heating

unit.2.

l The complete sauna system (sauna heating

unit, control unit, lighting system, etc.) may be

connected to the main power system by a

locally certified electrician only. All electrical

wiring installed inside the cabin must be suitable

for use at environmental temperatures of up to

140° C. Silicone cables are recommended. If

single filament cables are used, they must be

protected with flexible metal tubing. Minimum

diameters for connection cables and suitable

cabin sizes for specific heating output values

in kW are listed in Table 2.

l During installation of the sauna heating unit, it is

important to ensure that the vertical distance

between the upper surface of the sauna heating

unit and the sauna cabin ceiling is not less than

90 cm. The required horizontal (lateral) distance

between the sauna heating unit and the cabin

wall is shown in the dimensional diagram for the

each specific sauna heating unit. The distance

between the lower surface of the sauna heating

unit and the floor is also indicated in the dimen-

sional diagram. This distance is equivalent to the

height of the base for floor-mounted heaters. In

all cases, it must be ensured that the sauna

heating unit is not placed on a floor comprised

of easily flammable material (wood, plastic floor

coverings, etc.). Ceramic tiles are recommended

for sauna floors.

l The required distance between the heater

safety grate, the recliner bench or other

flammable materials to the sauna heating unit is

indicated in the dimensional diagram for each

specific sauna heating unit. The height of the

heater safety grate must be approximately

equal to the front height of the sauna heating

unit.

4,5 35 x 3

6,0 35 x 4

7,5 35 x 5

9,0 35 x 6

Power input in kW

Minimum dimensions of fresh-air

inlets and exhaust outlets in cm

Table 1

1 2 3 4 5 6 7 8 9

Comentários a estes Manuais

Sem comentários

EOS 38.AS Guia de Instalação Página 3

Comentários a estes Manuais